一、项目定位与页面数量
项目定位：面向全球客户的可持续包装解决方案网站，强调行业应用、认证合规、定制与全球交付，以 RFQ 询盘为核心转化路径；产品详情不采用购物车购买。
| 页面/类型 | 数量 | 确认程度及依据 |
| 首页 Homepage | 1 | 明确；4.1 |
| 行业解决方案页 Industry Landing Page | 9 | 明确：9 个行业；4.3 |
| RFQ 询盘页 | 1 | 明确；4.5 |
| 包材/产品详情页 | 未明确 | 4.4 给出模板，未列产品数量 |
| 认证与合规 | 未明确 | 导航栏目；有认证展示模块 |
| 解决方案 | 未明确 | 导航栏目，是否另有总览页未写明 |
| 工厂实力 | 未明确 | 导航栏目及工厂/产能展示 |
| 资源中心/博客 | 未明确 | 导航及资源中心/博客模块 |
| 联系我们 | 未明确 | 导航栏目；页面结构未写明 |
| 案例详情/其他 | 未明确 | 案例展示要求，但独立详情页数量未写明 |
结论：可直接计数的页面至少 11 页（1 首页 + 9 行业页 + 1 RFQ 页）。实际页面总数尚不能确定；不能把“9 个行业 × 8 个场景”直接等同于 72 个独立页面。
二、九大行业清单（客户原文）
| 序号 | 英文行业名称 | 中文行业名称 |
| 1 | E-commerce & Logistics | 电商物流 |
| 2 | Food & Beverage / Takeaway | 食品饮料外卖 |
| 3 | Electronics & 3C | 电子3C |
| 4 | Apparel & Textiles | 服装纺织 |
| 5 | Industrial & MRO | 工业MRO |
| 6 | Beauty & Personal Care | 美妆个护 |
| 7 | Pharmaceutical & Healthcare | 医疗健康 |
| 8 | Agriculture & Fresh | 农业生鲜 |
| vehicle make | Ford, GMC, Toyota |
|---|
Key parameters you need to confirm before ordering custom wheels
To ensure the forged wheels fit your vehicle perfectly, please confirm the following critical wheel parameters before placing your order: PCD (lug pattern), ET (offset), CB (center bore/hub bore), wheel size (diameter × width), and bolt spec (thread size).
1. PCD — Pitch Circle Diameter
It refers to the diameter of the circle formed by wheel bolt holes. For example: 5×114.3 means 5 bolt holes on a circle of 114.3 mm diameter. Wrong PCD will make wheels unable to mount onto the hub.
2. ET / Offset
Offset (ET value) is the distance between the wheel’s mounting surface and the wheel centerline.
Positive ET: mounting surface is outside the wheel centerline, wheel sits further inward toward suspension.
Negative ET: mounting surface is inside the wheel centerline, wheel sticks out further from the fender.
ET directly controls wheel position: inward flush or outward poke. Incorrect offset may cause tire rubbing against fenders or suspension parts.
3. CB — Center Bore / Hub Bore
Center bore is the central hole diameter on the back of wheel, which fits over the vehicle hub. The wheel CB must match or be larger than vehicle hub diameter. If wheel CB is bigger, hub-centric rings are required to eliminate vibration at high-speed driving.
4. Wheel Size (Width × Diameter)
Example: 18×9.5 (18 = wheel diameter in inches; 9.5 = wheel width in inches). Wheel width decides suitable tire width range.
5. Bolt spec (thread size)
Such as M12×1.5, M14×1.5. Confirm vehicle bolt thread specification for matching lug nuts.
Note: If you do not know these data, you can provide us your complete vehicle information: car brand, model, year, original wheel size. We will check and recommend suitable parameters for you.
How We Control Quality: From Raw Aluminum Bar to Finished Wheel
Every forged wheel goes through strict multi-stage inspection throughout the whole production process, from incoming raw material to finished product delivery, to guarantee safety, appearance and dimensional accuracy.
1. Raw Material Inspection — Aluminum Bar incoming check
Verify 6061-T6 aluminum billet chemical composition and mechanical property certificates. We conduct composition and hardness tests on every single aluminum bar. Reject unqualified aluminum bars before production.
2. Forging Process Inspection
Check forging temperature, pressing pressure and forming condition. Visual inspection for cracks, folds or surface defects after hot forging.
3. Heat-Treatment Inspection (T6 temper)
Monitor solution treatment & artificial aging temperature and time. Hardness test after T6 heat-treatment to make sure material reaches required mechanical performance.
4. CNC Machining & Dimensional Inspection
Precision dimension checking: PCD, ET(offset), CB center bore, wheel width & diameter. Run-out test to control circular run-out and face run-out. Thread hole inspection for bolt holes.
5. Surface-Treatment Inspection (Painting / Polishing / Brushing)
Visual check: no orange peel, no pinholes, no scratches, no paint leakage. Coating thickness test, adhesion test for paint layer. Salt spray test to confirm corrosion resistance performance.
6. Finished-Product Safety Test
Impact test, radial fatigue test, cornering fatigue test according to DOT / TÜV / JWL standards. Detect invisible internal cracks by penetration testing.
7. Final Full Inspection before Packing
100-percent visual appearance check.
To ensure the forged wheels fit your vehicle perfectly, please confirm the following critical wheel parameters before placing your order: PCD (lug pattern), ET (offset), CB (center bore/hub bore), wheel size (diameter × width), and bolt spec (thread size).
1. PCD — Pitch Circle Diameter
It refers to the diameter of the circle formed by wheel bolt holes. For example: 5×114.3 means 5 bolt holes on a circle of 114.3 mm diameter. Wrong PCD will make wheels unable to mount onto the hub.
2. ET / Offset
Offset (ET value) is the distance between the wheel’s mounting surface and the wheel centerline.
Positive ET: mounting surface is outside the wheel centerline, wheel sits further inward toward suspension.
Negative ET: mounting surface is inside the wheel centerline, wheel sticks out further from the fender.
ET directly controls wheel position: inward flush or outward poke. Incorrect offset may cause tire rubbing against fenders or suspension parts.
3. CB — Center Bore / Hub Bore
Center bore is the central hole diameter on the back of wheel, which fits over the vehicle hub. The wheel CB must match or be larger than vehicle hub diameter. If wheel CB is bigger, hub-centric rings are required to eliminate vibration at high-speed driving.
4. Wheel Size (Width × Diameter)
Example: 18×9.5 (18 = wheel diameter in inches; 9.5 = wheel width in inches). Wheel width decides suitable tire width range.
5. Bolt spec (thread size)
Such as M12×1.5, M14×1.5. Confirm vehicle bolt thread specification for matching lug nuts.
Note: If you do not know these data, you can provide us your complete vehicle information: car brand, model, year, original wheel size. We will check and recommend suitable parameters for you.
Related products
المراجعات
لا توجد مراجعات بعد.